How To Set Clock On Range Hood

USER MANUAL
HAUSLANE Kitchen Range Hood

Models UC-PS18-30 & UC-PS18-36

Rubber Data

Before installing your range hood, read the entire educational activity transmission. Installers, go out this transmission with the homeowner.

Alarm
SUITABLE FOR Apply IN HOUSEHOLD COOKING Expanse ONLY. TO REDUCE THE RISK OF FIRE, Electric SHOCK, OR INJURY, OBSERVE THE Following:

1. 1. 1. Utilize this range hood only in the style intended by the manufacturer. If you have the questions, contact Hauslane at 1-800-929-0168 or email at  [email protected]
      2. Before servicing or cleaning, switch ability off at service panel and lock service console to forbid power from being switched on accidentally. When the service disconnecting means cannot exist locked, securely spike a prominent alert device, such as a tag, to the service panel.
      3. Installation work and electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards, including fire-rated structure codes and standards.
      4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel-burning  equipment to prevent dorsum drafting. Follow the heating equipment manufacturer'south guidelines and safety standards such every bit those published by the National Fire Protection Association (NFPA), and the American Order for Heating, Refrigeration and Air conditioning Engineers (ASHRAE), and the local code regime.
      5. When cutting or drilling into wall or ceiling, practice not damage electrical wiring and other hidden utilities.
      6. Ducted fans must always exist vented to the outdoors.
      7. Do not employ this unit with whatever solid-state speed command device.
      8. To reduce the risk of fire, use only steel ductwork.
      9. This unit must exist grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. 1. 1. Never leave surface units unattended at high settings. Boil overs cause smoking and greasy spillovers that may ignite.
      2. Heat oils slowly on low or medium settings.
      3. Always turn hood ON when cooking at high heat or when cooking flaming foods.
      4. Clean ventilating fans oftentimes. Grease should not be allowed to accumulate on fan or filter.
      5. Use proper pan size. Always utilise cookware advisable for the size of the surface element.

WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE Pinnacle GREASE FIRE, OBSERVE THE FOLLOWING*:

1. 1. 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then plough off the burner. Exist Careful TO Forestall BURNS. IF THE FLAMES Practise NOT Exit IMMEDIATELY, EVACUATE AND CALL THE Burn down DEPARTMENT.
      2. NEVER PICK UP A FLAMING PAN equally you lot may be burned.
      3. Exercise Non USE WATER, including moisture dishcloths or towels. This could cause a tearing steam explosion.
      4. Employ an extinguisher Just if:
         A. You own a Class ABC extinguisher and you know how to operate it.
         B. The fire is small and contained.
         C. The fire section has been chosen.
         D. You can fight the fire with your dorsum to an get out.
         *Based on "Kitchen Burn down Condom Tips" published by NFPA.

Circumspection

1. 1. 1. For full general ventilating apply only. Exercise non use to exhaust hazardous or explosive materials and vapors.
      2. To avoid harm and noisy and/or unbalanced impellers, keep drywall/construction dust, etc. off the ability unit of measurement.
      3. Mount your range hood and then that the lesser of the hood is 24″ to 30″ to a higher place the cooking surface. The minimum hood distance above the cooktop must not be less than 24″; any installation less than 24″ may crusade overheating and crusade damage to the range hood, HAUSLANE does non warrant this improper installation.
      4. Two to iii installers are recommended because of the larger size and weight of this hood.
      5. To reduce the adventure of fire and to properly exhaust air, be sure to duct air exterior. Do not exhaust air into spaces within walls and ceiling or into attics, crawl space or garages.
      6. Considering of the high exhausting capacity of this hood, yous should make sure enough air is entering the house to replace wearied air by opening a window close to or in the kitchen.
      7. Use with approved cord-connection kit only.
      8. Please read product specification characterization on range hood for farther information and requirements.

Warranty Information

This range hood is warranted to the original purchaser to be free of defects in material and workmanship for 2 (2) years from the appointment of purchase.

Our obligation shall be limited to the repair or replacement of a unit of measurement (at our discretion) that may bear witness, by our sole examination, to be defective under normal use and service during the warranty period. We may issue credit in the corporeality of the invoice value of the lacking production (or a percentage of it co-ordinate to use) in lieu of repair or replacement. Whatever failure of this product that is non traceable to a defect in material or workmanship is not covered by this warranty. These non-warrantable items include, only are not limited to:

• • • Whatever defects or damage to light bulbs
    • Modify in colour or finish due to chemical usage
    • Improper installation non in accordance with the instructions
    • Dents, bumps, and scratches incurred during shipping, treatment, or installation
    • Impairment caused by failure to follow care and cleaning guidelines, including damage acquired by the use of abrasive cleaners
    • Alterations fabricated to the unit of measurement by the purchaser or installer
    • Damage caused by adventitious impact, fire, flood, freezing, and normal article of clothing
    • Bends and warping caused by forced connections, over-tightened fittings, and inadequate support during installation

A thorough inspection must exist made before installation and any damage must be promptly reported. We will not be liable for failures or harm that could take been discovered or avoided by proper inspection and testing prior to installation.

Incidental repairs that would involve a minimum of time and attempt on behalf of the purchaser will non be considered warranty piece of work and no compensation will be deemed forthcoming.

This warranty is non-transferable and shall exist voided if the unit is removed from its initial installation or if it is non installed following the instructions.

Under no circumstance shall we be held liable for personal injury or belongings damage resulting from improper installation or use of this product. We will not be held liable for inconvenience caused past loss of use of this product, costs incurred for labor or materials, removal and installation of replacement units, or any other incidental or consequential damages. Costs relating to obtaining access for repair or replacement are the responsibleness of the user.

This warranty does not extend to commercial and institutional installation or use.

Warranty Merits Procedure

If a claimable defect occurs, please contact our client service team at i-800-929-0168 (8 a.m. – 5 p.m., PST, Mon – Friday). or email united states at [email protected]
Before you lot make your claim phone call, delight ensure that you have:

• • • Description of the range hood
    • Proof of sale
    • Details regarding the defect
    • Proper name(s) and address(es) of the owner and installer

Claims must be filled out in writing and returned within vi (half-dozen) months of the appearance of a defect. Failure to comply with this stipulation will brand this warranty null and void. We reserve the right to a thirty-24-hour interval (thirty) filibuster following the receipt of a claim in which to audit the product. Nosotros assume no responsibility for labor costs, removing or replacing a previously installed product, transportation, or the return of a production.

Specifications

Package Contents

Tools Needed

Training: What to Do Before Installation

Before installing your range hood, carefully follow these steps:

ane. Read This Manual
Read through all the steps. If y'all fail to read the instructions advisedly, nosotros volition not be responsible for damages incurred on your part. If you're not confident in your abilities to install the range hood properly, we recommend hiring a certified technician to complete the installation.

2. Get together Your Tools
Ensure you accept all the necessary tools according to the previous folio.

three. Inspect the Unit
Unpack the unit and check your range hood for damage or missing parts. Plug information technology in to an outlet to ensure the fan and lights piece of work. If anything is damaged or missing, contact the seller to get the problems solved. Don't throw away packaging until you're sure you lot are fully satisfied with the product.

iv. Ensure There is Proper Height Clearance
To ensure the highest functioning, the bottom of your range hood must be between 24" and 30" from the meridian of the cooking surface. For gas ranges, the required distance is 30". Practise not exceed the maximum elevation of 30″ while in operation. This is very of import! Installing at the wrong height could lead to a desperate reduction in the range'southward performance or even cause a fire.

5. Bank check Your Power Supply and Ducts
Check to ensure your main voltage is in line with the required voltage outlined on the rating plate inside this hood. Too, check the domestic ability supply to guarantee acceptable earthing before installation.

This range hood must exist ducted to the outside. Don't connect the range hood to frazzle ducts that conduct any blazon of combustion fumes similar fireplaces, boilers, or any similar items. The vents should accept a short, straight run to the outside. Avoid any elbows if possible, and if an elbow is required, a minimum of a 12" directly run is imperative before the elbow.

half-dozen. Figure Out Ducting Requirements & Install Adapter
This range hood requires ducting to the exterior for ventilation. This range hood comes pre-installed with a vertical six" circular adapter. The parcel comes with a horizontal and a vertical rectangular adapter.
Look at the duct you're going to adhere the range hood to.

Is it a vertical rectangular duct?
If so, take off the round adapter that is preinstalled on the unit of measurement by removing 10 screws. Adhere the rectangular adapter in its place and tighten the adapter with the previously-removed x screws. Remove the record holding up thedampers.
IMPORTANT: Failure to remove the record from the damper will cause reduction in performance.

Is it a 6" round duct?
You won't have to make whatsoever extra preparations. The range hood volition attach directly to your duct. Be sure to remove the tape holding up the dampers.
IMPORTANT: Failure to remove the tape from the damper volition cause a reduction in performance. Make certain to install the existing black rubber gasket.

Is it a horizontal rectangular duct?
If and then, remove existing round adapter by removing the ten screws. Cover the opening with the shutoff plate and secure with ten screws. This renders the round duct opening useless, and you can move forward with the installation of proper arrangements for horizontal discharge.

Remove the 5 screws and carefully take off the big shutoff plate on the dorsum of the hood. Then, advisedly remove the eight screws holding the minor sealing hat within the dorsum of the hood.

Attach the horizontal rectangular adapter into the back of the hood. Attach it using the 8 screws you lot removed from the pocket-sized shutoff plate. Remove the tape holding upward the dampers.

IMPORTANT: Failure to remove the tape from the damper will crusade reduction in performance. Make sure to install with the existing black condom gasket.

vii. Prepare the Cabinet (Soffit)
Measure the size of the outlet adapter relative to the cabinet. If it is non already done, you'll demand to cut an opening in the chiffonier to ensure the outlet adapter and power cable can pass through. If you must do this, use a pencil and ruler to mark the area, then cutting with a wall/keyhole saw.

If you're installing the UC-PS18SS-30 nether a cabinet with a recessed bottom, we recommend using 4" wood fillers on each side to stabilize the cabinet for mounting purposes. For UC-PS18SS-36, we recommend using 6" wood fillers on each side for easier, more than secure mounting.

9. Find a Helper
This range hood is best installed past two or more than people due to its size and weight. Again, it is recommended to hire a certified technician for installation to reduce the risk of damage or injury.

UC-PS18-thirty
1. Round Vertical Adapter

two. Rectangular Vertical Adapter

3. Rectangular Horizontal Adapter

UC-PS18-36
1. Round Vertical Adapter

two. Rectangular Vertical Adapter

3. Rectangular Horizontal Adapter

How to Install Your Range Hood

When you've completed all the grooming steps, you lot're ready to install your range hood.

1. Test the Unit
Plug the unit into an outlet and press the touch panel to make sure that the unit is working.
Of import: If the range hood is non working properly, delight contact us immediately (i-800-929-0168 / [email protected]).
2. Uninstall the Range Hood'due south Bottom Comprehend
Remove the baffle filter from the hood by pushing the filter knob inwards. Slowly pull the filter downward and remove gently from the range hood. Then, remove the bottom cover by carefully unscrewing the eight screws as shown.

3. Jack Up the Hood
If you are not removing the range, place the plywood (30" 10 24") over the range / cooktop to avert possible damage. Put the chiffonier jacks on the plywood and place the second slice of plywood over the two cabinet jacks. Using the cabinet jacks, lift the hood into its position under the cabinet. Ensure that the adapter and power string enter the cabinet openings and that the power cord is not pinched between the hood and the cabinet.

If you practise not wish to use a cabinet jack, you will demand iii people. Have 2 helpers property the range hood in identify while the third person inserts the screws to mount the range hood. For cabinet jack operation, please refer to its manual.

four. Screw It Into Place
From the bottom of the hood, carefully insert the mounting screws (AA) with washers into each of the pre-drilled mounting holes in the range hood. Beginning with  the front left, so front correct. After the screws are in identify for the front mounting holes, work on the rear left, and so rear right. If y'all feel that you need to install the range hood more securely, yous can use the additional two mounting spiral holes in the front/center.

TIP: To easily reach the rear mounting holes, utilize an extension tool for the ability drill.

5. Double-Check Installation and Remove Support
Exist sure that the hood is securely attached earlier removing the cabinet jacks and plywood.

vi. Connect Damper & Bank check for Airtightness
Turn on the hood to make sure that the damper opens and closes freely. This will ensure better and quieter performance. Insert the duct into the adapter, then attach with the two previously loosened screws. Make certain the duct is firmly attached to the adapter and wrap the joint with aluminum foil tape to brand it air-tight.
Of import: Exist careful when connecting the vent pipe to the adapter. Excessive force might dislodge the damper and brutal into the house, which may impairment the motor.

7. Plug the Range Hood In
Plug the power cable into an outlet.

8. Reinstall Bottom Embrace, Baffle Filters and Grease Collector
Using the 8 screws you removed earlier, reinstall the bottom comprehend and then reinstall the baffle filters. Finally, carefully insert the grease collector.

9. Keep This Manual
Put this transmission in a safety place and go along for further

How to Use Your Range Hood

Now that your range hood is installed, it's time to learn how to employ information technology. It is very unproblematic to use and is operated entirely using the front control panel.

1- ON/OFF
2- LIGHT
3- DOWN
4- Upwards
5- TIMER DELAY

How to Turn Light On/Off
This range hood has a unmarried light setting. Printing the lightbulb button (2) to turn the light on or off.
Caution: For element of group vii lamps never affect bulbs during operation; they tin can get very hot.

How to Set the Fan Speed
Press the on/off button (ane) to turn the range hood on. To increase/decrease fan speed, utilize the up/downward arrows (three & 4) to find your desired fan speed.

How to Set the Clock
Press the on/off push button for 3 seconds. When the time starts flashing, touch the upwards and down arrows (3 & iv) to reach the desired hour. Then, press the on/off push button in one case once again to set the minutes using the up and down buttons.

How to Set the Timer Delay
This range hood has a timer delay button that comes in handy if you demand to employ your hood for a prepare flow of time. While the fan is operating, press the timer filibuster button (5). When the timer filibuster indicator comes upward on the display, touch on the up and downwards buttons to set the timer anywhere from 1 to xv minutes.

Basic Maintenance Instructions

Your range hood requires some easy routine maintenance to proceed it running efficiently.

Maintaining the Baffle Filter
Clean the grease filters frequently—we suggest cleaning every 2 weeks. For your convenience, the filters are dishwasher prophylactic!

1. 1. 1. Remove the baffle filters from the hood by pushing the filter knob inward. Then, advisedly pull the baffle filter down and remove it gently.
         
      2. Clean the baffle filters with warm h2o and detergent, or place them in the dishwasher. Exist careful with the filters to avert damage.
      3. Let the baffle filters dry completely.
      4. Reinstall the baffle filters.

Maintaining the Lighting

 This range hood uses ii lamps of 3W.

1. 1. 1. Turn off the power. For halogen lights, let light bulbs cool completely before removing if needed (about 5 minutes).
      2. Wearing protective gloves, rotate the low-cal bulb counterclockwise to disengage the bulb.
      3. Identify new lightbulb into the socket and rotate

Cleaning Your Range Hood
This range hood will expect great and function correctly for a long time with proper care. Here are a few exercise'south and dont's when caring for your range hood.
WARNING: Failure to maintain bones standards of intendance and cleaning will increase the risk of fire.

Wiring Diagram

Troubleshooting Tips

Alert: Failure to maintain basic standards of intendance and cleaning will increase the risk of fire.

Problem / Solution

• • • My range hood won't work.
      • 1. Brand sure the power supply and wiring are connected securely.
      • 2. Double-bank check to see that the power breaker is on and the power supply is live.
      • 3. Cheque to see that the command panel cables are continued correctly to the switchboards.
    • My range hood vibrates while the fan is operating.
      • 1. Bank check to ensure the hood is firmly secured to the cabinet/wall. Tighten or add screws if necessary.
      • 2. Confirm that the motor is firmly in place and secured safely. If it is non, tighten information technology.
      • 3. If those steps oasis't resolved the issue, your fan may be damaged. If information technology is damaged, you may need to supervene upon it.
    • The fan is operating weakly
      • one. Double-check to ensure the duct size is right.
      • 2. Make clean ducts or filters if they're dirty. Too, bank check to brand sure the mesh enclosure on the hood is receiving proper air ventilation.
      • three. If possible, check to see that the damper is functioning properly regarding the opening.
    • The fan is not working properly even though the lights are working.
      • 1. Double-bank check that the fan is not jammed /that it isn't scraping any of the surfaces of the hood.
      • ii. If this doesn't work, you may need to replace the motor every bit it may be defective.
    • The vent hood is not working efficiently
      • i. The minimum distance between the cooking area and the appliance should exist 24″ or xxx″ maximum. Check to see if this is correct.
      • 2. Make sure that the duct is not susceptible to easy wind opening.
      • 3. Make sure the fan speed is at the advisable rate. The heavier the cooking, the greater the speed of the hood should be set.
      • 4. Closing the windows and doors in the room will permit the vent to work much meliorate.
      • 5. Equally noted during the installation process, all ductwork must be done correctly. Yous may need to reduce the length of the ductwork or reduce elbows.
      • 6. Brand sure all joinery in ductwork is sealed and secured properly.
    • The light is not working.
      • 1. Check to see if lightbulb is loose and needs to be tightened.
      • 2. If tightening doesn't fix the problem, replace bulb with a new one and see if that solves the consequence.
      • 3. If replacement and/or tightening does not solve, you may need to replace the lighting service organization on the hood.
    • The touch panel is not responding.
      • one. Perform a power cycle reset by unplug the ability string, wait 10 seconds, and plug the power cord back.
      • 2. If Stride 1 doesn't resolve the issue, please contact us immediately for a control panel replacement.

Yet, experiencing problems after post-obit these steps? Contact a technician to assistance. Contact u.s. at i-800-929-0168 or [email protected]

Contact Hauslane

Extended Warranties
If you lot are interested in an extended warranty, sign up on our website at www.hauslane.com

Parts and Accessories
If you lot need replacement parts or accessories, visit www.hauslane.com

Contact United states of america
We'd be happy to answer your questions or resolve any problems you may have.
Phone: 1-800-929-0168

Find Us and Connect with Us

http://www.chefkitch.com

Kitchen Range Hood UC-PS18-30/UC-PS18-36 User Manual – Optimized PDF
Kitchen Range Hood UC-PS18-30/UC-PS18-36 User Manual – Original PDF

Source: https://manuals.plus/hauslane/kitchen-range-hood-uc-ps18-30-uc-ps18-36-manual

Share this post